Beyblade Beystadium vs Rotary Tools
Subject: Beyblade Beystadium
Series: Beyblade
Test Date: June 14, 2003

Materials:

WE ARE PROFESSIONALS: DO NOT TRY THIS TEST AT HOME!

Beyblade Beystadium
Phase One:

The Beyblade Beystadium was placed on an old picnic table outside Adequate.com's main office. The stadium included two small tops and a launching spinner for each. The stadium itself had a blue arena floor which would spin when the blue controls on the side were pulled out and pushed in.

Tops get spinning
We started off by letting the tops spin the way the manufacturers intended. The tops had a relatively low RPM. Neither was powerful enough to knock the other out of the stadium. Pulling the levers made the tops spin around the arena more, but had little or no effect on the "battle". The tops were clearly not powerful enough. The stadium doesn't draw a sell-out crowd
Phase Two:

To provide more power to the tops, we selected a Dremel MultiPro Cordless 7.2V Model 770 Type 1. It features speeds of either 7,500 RPM or 15,000 RPM...not to mention the popular 0 RPM "OFF" setting.

Dremel MultiPro Cordless
The white Beyblade top was placed at the end of a small screw attachment. It was firmly connected so that it would spin at the same rate as the rotary tool. Locked and loaded
We started off spinning the top at a rate of 7,500 RPM. Look at it go!
For the competition, we chose a Craftsman Variable Speed Rotary Tool to power the other top. From the fine folks at Sears
Phase Three:

With the tops mounted on the Dremel and Craftsman tools, it was time to do battle.

We increased the Dremel's speed to 15,000 RPM to make the fight fair.

Battle!
Applying a downward pressure, the tops began to leave marks on the stadium floor. This is the first sign of any damage to any pieces. Notice the stadium begins to suffer damage
The white top eventually came off, but the black/grey one kept going.

Note the additional damage to the stadium.

A new land speed record for Beyblade
Phase Four:

With the white top no longer able to stay connected, the Dremel's attachment was changed to a grinding tool.

Bump and grind
Phase Five:

The white top was brought back into service. The grinding attachment was replaced with a drill attachment.

The drill spun the top, but also went through the bottom of the top and through the stadium floor.

Drilling straight through
In this close-up photo, you can see through the white top.

You may also notice damage to the edges of the tops.

Examine the tops
Phase Six:

After coming to the conclusion that the tops alone were not enough to damage the Beystadium, we changed to a hole cutter on a Black & Decker 3/8" drill.

Rather than leaving on only the hole saw for one size of hole, we left on all the hole saws.

Makes holes wherever you need them
The tops and the decorative lighting from the side of the stadium were placed inside. We did not put the spinners inside because they contain metal springs. (We're not stupid!)

Once inside, the stadium's lid was closed.

Closing the coffin
The hole saw was lined up and we started drilling dead-center on the stadium's cover. This is where it gets good
Once the center of the drill penetrated the lid, the hole saws came crashing down. The friction from all the spinning saws caused the whole stadium to start spinning at thousands of revolutions per minute. Imagine if you were inside
When the saw was removed, you could see that the top was fairly well dug up. So much for that top sticker
The spinning became so uncontrollable that the entire stadium flew off the table. At this point, the cover flew off and the contents of the stadium went flying. (That white blur is the white top.)

Note how the table has been sanded down from the spinning stadium.

Whitey makes a break for it!
Phase Seven:

With the cover gone, we removed the inner hole saws and drilled directly into the Beystadium. The hole was started off-center so that the stadium floor would not spin with the drill.

At this point, it's a lost cause
Damage Assessment:
The bottom of both tops have been worn flat. Both tops have holes through the center. The Beystadium has suffered extreme damage due to the hole cutter. The cover came off, but can be reconnected.

Conclusion:
Beyblade tops and the Beystadium were not designed to withstand high rates of speed, downward pressure, and hole cutters. In summary, Beyblade is boring. Beyblade with power tools is fun.

Look for video from this experiment at The Chibi Project's convention appearances and coming up in the podcast.

Let it rip with your own Beyblade Mobile Beystadium or other Beyblade toys from Amazon.com.

Beyblade Beystadium after the earthquake
Beyblade Beystadium from the bottom