The Chibi Project

Beyblade Beystadium vs. Rotary Tools

Beyblade Beystadium Subject: Beyblade Beystadium
Series: Beyblade
Test Date: June 14, 2003



Testing Procedure

Tops get spinning Phase One:

The Beyblade Beystadium was placed on an old picnic table outside's main office. The stadium included two small tops and a launching spinner for each. The stadium itself had a blue arena floor which would spin when the blue controls on the side were pulled out and pushed in.

The stadium doesn't draw a sell-out crowd

We started off by letting the tops spin the way the manufacturers intended. The tops had a relatively low RPM. Neither was powerful enough to knock the other out of the stadium. Pulling the levers made the tops spin around the arena more, but had little or no effect on the "battle". The tops were clearly not powerful enough.

Dremel MultiPro Cordless Phase Two:

To provide more power to the tops, we selected a Dremel MultiPro Cordless 7.2V Model 770 Type 1. It features speeds of either 7,500 RPM or 15,000 RPM...not to mention the popular 0 RPM "OFF" setting.

Locked and loaded

The white Beyblade top was placed at the end of a small screw attachment. It was firmly connected so that it would spin at the same rate as the rotary tool.

Look at it go!

We started off spinning the top at a rate of 7,500 RPM.

From the fine folks at Sears

For the competition, we chose a Craftsman Variable Speed Rotary Tool to power the other top.

Battle! Phase Three:

With the tops mounted on the Dremel and Craftsman tools, it was time to do battle.

We increased the Dremel's speed to 15,000 RPM to make the fight fair.

Notice the stadium begins to suffer damage Applying a downward pressure, the tops began to leave marks on the stadium floor. This is the first sign of any damage to any pieces.
A new land speed record for Beyblade

The white top eventually came off, but the black/grey one kept going.

Note the additional damage to the stadium.

Bump and grind Phase Four:

With the white top no longer able to stay connected, the Dremel's attachment was changed to a grinding tool.

Drilling straight through Phase Five:

The white top was brought back into service. The grinding attachment was replaced with a drill attachment.

The drill spun the top, but also went through the bottom of the top and through the stadium floor.

Examine the tops

In this close-up photo, you can see through the white top.

You may also notice damage to the edges of the tops.

Makes holes wherever you need them Phase Six:

After coming to the conclusion that the tops alone were not enough to damage the Beystadium, we changed to a hole cutter on a Black & Decker 3/8" drill.

Rather than leaving on only the hole saw for one size of hole, we left on all the hole saws.

Closing the coffin

The tops and the decorative lighting from the side of the stadium were placed inside. We did not put the spinners inside because they contain metal springs. (We're not stupid!)

Once inside, the stadium's lid was closed.

This is where it gets good

The hole saw was lined up and we started drilling dead-center on the stadium's cover.

Imagine if you were inside

Once the center of the drill penetrated the lid, the hole saws came crashing down. The friction from all the spinning saws caused the whole stadium to start spinning at thousands of revolutions per minute.

So much for that top sticker

When the saw was removed, you could see that the top was fairly well dug up.

Whitey makes a break for it!

The spinning became so uncontrollable that the entire stadium flew off the table. At this point, the cover flew off and the contents of the stadium went flying. (That white blur is the white top.)

Note how the table has been sanded down from the spinning stadium.

At this point, it's a lost cause Phase Seven:

With the cover gone, we removed the inner hole saws and drilled directly into the Beystadium. The hole was started off-center so that the stadium floor would not spin with the drill.

Beyblade Beystadium from the bottom

Damage Assessment:
The bottom of both tops have been worn flat. Both tops have holes through the center. The Beystadium has suffered extreme damage due to the hole cutter. The cover came off, but can be reconnected.

Beyblade tops and the Beystadium were not designed to withstand high rates of speed, downward pressure, and hole cutters. In summary, Beyblade is boring. Beyblade with power tools is fun.

Additional Information

Beyblade Beystadium after the earthquake

The Beyblade Beystadium can be seen in episode 21 of The Chibi Project Podcast.

Buy Your Own